What Wenger builds
Wenger Manufacturing describes itself as a global leader in extrusion cooking systems, offering complete process solutions for plant-based proteins, pet foods and aquatic feed. The company is headquartered at 15 Commerce Drive in Sabetha, Kansas, with contact locations in Taiwan, Belgium, Brazil and China. It markets its work as more than 90 years of innovation.
Its history page dates the start to 1935, when brothers Joe and Lou Wenger formed the Wenger Mixer Company to add molasses to low-value roughage for cattle feed. Extrusion experiments began in 1939, the cooking extruder followed in 1958, and a twin screw extruder in 1985. In 1973 the company expanded into snacks and textured vegetable proteins.
The page states that by 2000 more than 80 percent of the world’s pet food was made with Wenger extruders. Marel, a global food processing company, acquired Wenger in 2022. For a protein developer the point is practical: texturised plant proteins such as textured vegetable protein are made on extruders, so equipment shapes fibre, density and cost.
Extruder lines and dryers
The product range covers the Magnum ST series, Thermal Twin, PetFLEX, AquaFLEX, C2TX conical, Optima and forming extruders. Dryers and ovens include high capacity horizontal dryers and coolers, sanitary dryers, a convection roaster, light duty ovens and a heat recovery unit. The site lists food, pet food, aquatic feed and industrial markets separately.
The Magnum ST series uses parallel-shaft twin screws built for high specific mechanical energy. The page states screw speeds of up to 1,200 rpm and power of up to 165 kWh per tonne at volumetric capacity. High energy input can give lower bulk density, higher absorbency of coatings, smaller cell structure and higher cook levels, per the series description.
The technical table lists the TX-57 at 57 mm screw diameter with up to 1,700 kg per hour and 188 kW, the TX-85 at 4,800 kg per hour and 450 kW, and the TX-144 at 22,700 kg per hour and 2,250 kW. These are volumetric maxima, so throughput for a given recipe needs a trial.
Texturised protein and meat analogues
The food page says Wenger has worked with textured vegetable proteins since they were first developed in the 1960s, and has kept improving extrusion systems, dies, controls, dryers and coolers. Supported protein sources include soy, pea, chickpea, wheat gluten, lentil, lupin, rice and other legume-based proteins. Details of each recipe depend on the protein isolate, the moisture and the die.
Product types named include textured vegetable protein as nuggets, chunks, strips, milled, minced and flaked forms, and high moisture meat alternatives that imitate whole-muscle beef, poultry, pork, fish and turkey. The page also lists structured meat analogues, fibrous soy proteins, textured meat proteins and hybrids, protein crisps, breadcrumbs, cereals, snacks, reformed rice, pasta and co-extruded products.
For developers, the line between dry and wet texturisation matters. Dry extrusion, followed by drying, yields low-moisture pieces that are rehydrated by the customer, while high moisture extrusion with a cooling die gives a fibrous, ready-to-use mass. A related entry on textured pea protein covers the ingredient side, including how the starting protein affects the result.
Technical centre and services
The Wenger Technical Center opened in 1965 and was expanded and reopened in 2021 as an agrifood laboratory with research-scale and production-scale extrusion and drying equipment. The services section describes an innovation lab of 25,000 square feet for testing concepts and production runs. Customers can trial a protein on pilot equipment before investing in a line.
Trial design deserves attention. A useful run documents the protein source and its lot, moisture, feed rate, screw speed, temperature profile, die configuration and cutting setup, together with the texture, density and yield of the output. Without that record, results are hard to transfer to another machine, and a later scale-up has no reliable baseline to work from.
Wenger lists design features on the Magnum ST such as a high intensity preconditioner, a roll away feature, a dry ingredient feed system, barrel and shaft removal, an overhead rail system and an automated process management control system. Such features affect cleaning time and changeover, which matter for plants running several proteins.
How a buyer would evaluate the supplier
Start with the product. Define the protein sources, the target format, the moisture window and the hourly capacity, then ask Wenger to propose a machine and die package and run it at the technical centre on the actual protein lot. Request the trial report, energy balance and wear parts list, so costs per tonne can be compared.
Next, examine hygiene and service. For food lines, ask about sanitary design, access for cleaning, material certificates for contact parts and the validation support offered. Ask where spare parts and technicians are located for the plant’s country, since contact locations are listed for Taiwan, Belgium, Brazil and China, and agree response times for production-critical failures.
Finally, review the downstream chain. Extrusion is one step: protein premixing, preconditioning, cooling, cutting, drying and packaging each influence yield and quality. Compare turnkey scopes with split purchasing, and confirm who carries responsibility for line performance. Buyers can also contact the company at its main telephone listing for feasibility questions before committing to trials.